Colour Changing LED Bars - 2.1 Million Colours

Our latest product - RGB LED Bars. Ideal for use in areas where our RGB LED Tape would not be quite powerful enough, these LED Bars project the light onto nearby surfaces.

The LED Bars have a very thin profile of just 8mm.

Ideal for: Lighting behind glassware, lighting architraves & alcoves, backlighting Plasma/LCDs, Home Cinema lighting etc

Each LED Bar uses a primary colour LED; Red, Green, and Blue. By projecting various levels of each colour upto 2.1 million colours and shades are possible!

Safe low voltage - 12vdc.

The LED Bars are controlled via the ICELED Flexidriver, it has a standalone mode which allows a gradually colour phasing, any colour can be locked by briefly switching the power off and back on within 1-2 seconds, to unlock simply repeat. Even more control is possible including sound activation by using the ZAP+ or ZEN Controller.

Click here to see how it's connected.

For simplicity we would recommend the ZAP+ Controller. Advanced setups such as zones will require a ZEN Controller. The Tape can also be linked to any of our other Mood Lighting products.

Safe low voltage - 12vdc, very energy efficient just 3.6 watts per foot!

The 120 degree LEDs are placed closeley together along the entire length of the bar which produces a bright colour wash with no dots or hotspots.

The LEDs are housed in Polycarbonate Bars making them very rugged and fully waterproof - IP68. The bars are flat just 8m deep by 14mm wide and can flex to follow virtually any contour.

Each LED Bar includes clips, self-tapping screws, and instructions.

300mm RGB LED Bar (54LEDs) - £24

800mm RGB LED Bar (135 LEDs) - £39

1200mm RGB LED Bar (216 LEDs) - £44

ICELED Flexidriver to control colours (will power up to 14.5 Meters [50ft] of LED Bars) - £35

Extra Control

ICELED ZAP+ (wired) Controller (Will control upto 11.5ft of LED Bars) with sound control - £38.

ICELED ZEN (infra-red remote) Controller (Will control up to 33ft of LED Bars) with audio line-in for sound to light effects - £78

Choose the controller that is suited for the amount of LED Bars you wish to power.

Power Supplies

Plug-in 1.25A Switch Mode Power Supply (Capable of powering up to 1 x 1200/800mm LED Bar, or 2 x 300mm LED Bars, or 1 x 800mm Bar) - £7.00

In-Line* 3.8A Switch Mode Power Supply (Capable of powering up to 12ft of LED Bars in total, that is 3 x 1200mm Bars) - £19.00. Discount for Quantity.

In-Line* 5A Switch Mode Power Supply (Capable of powering up to 15ft LED Bars in total, that is 5 x 1200mm Bars) - £25.00. Discount for Quantity. Use with the ZEN Controller.

In-Line* 10A Switch Mode Power Supply (Capable of powering up to 30ft LED Bars in total, that is 10 x 1200mm Bars) Meters of tape in total) - £25.00. Discount for Quantity. Use with the ZEN Controller.

*In-Line Power Supplies have a removable Mains plug for permanent installations i.e through a (fused) light switch.

Power Supplies

LED Type: Top Hat LED

Voltage: 12vdc

Current per foot length: 300ma.

800mm Bar - 800ma

1200mm Bar - 1200ma/1.2A

Sizes given are the illuminated length, below is the exact overall length allowing for cable exit:

300mm Bar - 330mm

800mm Bar - 830mm

1200mm - 1235mm

ICELED Flexidriver can be used with or without an external controller. A built-in programme allows it to perform a variety of functions simply by connecting to a 12 Volt DC supply.

Full easy to follow instructions are included to help you get the best out of the product.

Flexidriver Specifications

Nominal Supply Voltage: 12vdc

Maximum Switched Current: 5 Amps (per channel)

Maximum "through" current: 15 Amps

Maximum Load: 180 wats @ 12vdc (25 Meters LED Tape)

Data accepted: Global ICELED, DMX via ICELED Bridge, UFO Tube segment 0, pixel 0

Colours: 2,097152. 7 Bit 128 Levels.

Dimensions of Flexidriver: W 50mm, H 15mm, D 65mm