(2) Colour Changeable (RGB) LED Tape - Splashproof
Below: RGB LED Tape can display Warm White
Below: Matching the colour to the grass outside!
Colour Changing Flexible LED Tape - 16.7 Million Colours!
Flexible RGB LED Tape is one of the most streamline light sources currently available, it can display the full visible spectrum of colours. It can be trimmed to length and off-cuts reconnected for use elsewhere.
This is our latest Professional Grade version with branded LEDs and a protective Silicone Coating over Resin on all sides giving the product an extremely durable and splash proof finish. This is one of the best grades of LED Tape available, don't risk installing anything less!
RGB LED Tape can display any colour including White and pastel shades of White including Warm White.
It is ideal for use where you need linear light source such as shelves, bookcases, kitchen plinths, worksurfaces, picture rails etc.
Powered from a safe low voltage of 12vdc.
LED Tape can be powered from the mains via one of our Power Supplies which converts mains voltage to the low voltage required to power the LED Tape.
It is suited for use in humid or wet areas such as kitchens and bathrooms where it will get exposed to moisture. Professional Grade LED Tape will not split or crack.
The protective coating also allows it to be easily wiped clean removing dust and grime without risk of damaging the joints between the LED and the Flexible Strip the LEDs are soldered to.
The RGB Tape uses a 3 Colour RGB LED; Red, Green, and Blue. By mixing varying levels of each colour up to 16.7 Million colours and shades are possible!
It can display any colour including white and pastel shades of white including warm white.
The brightness of the product makes it ideally suited where a linear light source is required such as a ceiling uplight around coving or for use in or around architraves, under kitchen plinths, to illuminate shelves, book cases, work surfaces, picture rails and so on. It can flex around convex and concave contours.
Brightness, Hue, and Saturation can be controlled by using a ZEN or Lightbox Controller (see further down this page)
The LED Tape itself is thin with a depth of just 4.5mm. It has a 3M self-adhesive backing so is easily applied to most smooth surfaces by simply removing the backing paper. Additional fixing clips are included to help secure the product in place.
It is finished to a high standard, it can be easily cleaned with damp tissue.
The LEDs produce a wide light dispersion (120 degrees) which gives a reflected glow similar to that of neon from nearby surfaces and objects. There are no dots or hotspots.
The Tape can be cut / joined to make any length you need, connections and cutting points are at 3 LED (100mm / 4inch) intervals. Full instructions are included.
Our RGB Tape is supplied with 400mm of connecting wire pre-fitted this can be easily extended by using our 4-core extension cable.
The LED Tape is controlled via the Flexi Driver, it has a standalone mode which allows a gradually colour phasing, any colour can be locked by briefly switching the power off and back on within 1-2 seconds, to unlock simply repeat.
Even more control is possible including sound activation by using the ZAP+ or ZEN Controller.
For simplicity we would recommend the ZAP+ Controller. Advanced setups such as zones will require a ZEN Controller. The Tape can also be linked to any of our other Mood Lighting products.
RGB LED Tape is suitable for use in or outside the home and is ideally suited for commercial use in Conference Rooms, Hotels, and Restaurants. Our ZEN Controller allows a few meters to hundreds of meters to be controlled from one Remote.
We have put together various lengths below allowing you to choose the nearest to your requirements, remember it can be trimmed every 100mm, we include 2 free end caps with every length to seal the end for a professional finish.
Choose a product for details, purchase options & accessories
The Colour changeable RGB LED Tape can be used with just a Flexi (2.1 Million) Colour Driver for smooth colour phasing.
For additional speed, palette and sound to light control you can add a ZAP or ZEN Controller to the system.
Our latest addition are the Lightbox and WLightbox for Smartphone and Tablet Control.
Please choose the correct power supply based on the total length of LED Tape you want to power.
The Colour Changing (RGB) LED Light Strip is now double encapsulated. First the LED Strip is completely encased in a flexible resin on the front, back and sides, then a Silicone Tube is extruded around that. This makes the final LED Tape extremely rugged and hard wearing. Any water or moisture that penetrates the outer Silicone Tube is not going to be able to get past the protective resin seal.
We include end caps allowing the LED Tape to be trimmed and resealed.
For installations where Strip Lighting is required to go around corners such as on top of pelmets there are a couple of options:
Option 1) You could purchase the LED Tape so it can be trimmed and capped at each corner and start another length of LED Tape for the next wall, so for all 4 walls you would require 4 lengths of LED Tape, each length of Tape would have its own power cable from the Flexi Driver or could be spliced into a heavy duty 4-core cable.
Option 2) The LED Tape can be cut to the nearest 100mm (4 inches) short of where the corner starts, then solder link wires to carry the voltage to the next length of LED Tape. 6 Meters is the maximum recommended continuous or joined length. For example you could have a 3 Meter length joined to another 3 Meter length, or a 4 Meter length joined to a 2 Meter length.
Below, our LED Strip with 4 Zone Wireless Control fitted into a conference room. Our Strip and Tape can also be controlled by DMX either from a console or even iPad, iPhone, or Android Device with a DMX App.
The video below is of our LED Tape installed in a trendy bar / club back in 2007. We are now on 3rd and 4th Generation LED Light Strips.